Frussrtrating audio project, 1:55

Let’s start with the SSR audio upgrade project which at this point I am considering to be finally finished.

Those of you that are familiar with the project know I had the radio in the car but there were a number of warts with the install such as very low voice guidance volume as well as low overall radio volume, fit issues where the faceplate of the radio was causing the dash to bulge out just enough to cause the HVAC controls to bind, sound that was bouncing back and forth between the speakers and I hadn’t done any of the work to mount the rear view camera.

In my research regarding the volume problem the first step recommended was to tweak the potentiometer on the GMOS-04 adapter to increase the signal fed to the amp. Of course to do this I had to rip the entire dash apart again.  I actually went a step farther and removed the top dash cover.  The reason I did that was to allow me better access to the back of the radio, hoping to be able to better place/organize the huge collection of wire/connectors/modules that are associated with the install.

Turning up the dial on the GMOS-04 did indeed appear to address my volume issue.

In addition to the top dash pad I had the “waterfall” removed as well.  I read there was a fuse box behind there where I could splice in the reverse signal wire, the wire that flips the radio to rear camera view when the truck is put in reverse.  At one point I had the interior of the truck so ripped apart that I was feeling a bit despondent, I questioned my ability to get everything back together in an acceptable manner.

I then turned my attention to getting the rear camera installed.  I had scrapped my idea of getting my reverse signal from the waterfall fuse box.  The location of the wire I was supposed to tap into was really in a bad spot.  I instead decided to just tap into the back up light harness in the back of the truck and then just run that wire along with the camera wire back to the passenger compartment.

Based on a SSRFanatic’s advice I put both wires inside of a wire loom to protect them from the elements.  Routing them up to the front of the truck was a bit challenging, it was tough finding a route that did not get close to the exhaust system.    I used zip ties to hold the loom in place along the way.

Once I got up to the passenger compartment I needed a way to get into it.  I didn’t see any easy way to do so, so I made my own, drilling a small hole in the floor of the SSR under the passenger side sill cover.  I then fed the wire loom through that hole.  The camera wire went to the control box I had behind the passenger seat, the reverse signal wire was routed up to the radio harness.

Originally I had ideas of maybe soldering my wire connections in the harness instead of just relying on wires twisted and then crimped in bell caps.  I decided to not go that route, instead I used small wire ties around the wires to further provide stress relief.

So I finally thought I was in the home stretch, I had everything back together and was ready to call the job DONE.  I took the SSR out for a quick road test and was immediately annoyed.  I was annoyed by the distinctive sound of alternator whine coming through the speakers.  The sound followed the rpm’s of the truck.  I hadn’t heard this noise before because all of my testing was with the engine turned OFF. Well I knew this would drive me nuts so I had no choice but to rip the dash open AGAIN.

Upon reading on the internet about alternator whine it indicated this can often be caused by a faulty ground.  Well I tested my ground, it appeared rock solid.  I then took turns disconnecting one connection at a time on the harness to see if I could isolate one component causing the issue.  I spent a TON of time screwing with it but got nowhere.  I was really frustrated.

Well on a whim I decided to try backing the potentiometer on the GMOS-04 back down a bit.  When I had the volume problem initially I could turn the radio to max volume and not have things all that loud.  After my tweak at half volume it sounded like it was ready to blow the speakers.  So I backed the dial back about halfway between where I started and where I finished.

That seemed to help, I heard a faint whine but hardly discernible, I could only guess the GMOS-04 was just adding too much gain.  I put the damn thing back together one final time and called it good enough.

At one point when I was in the midst of installation hell I was mildly complaining to Ali about it.   She said to me, and correctly so “Well this is what you got it for right?”  I did indeed want a vehicle as my hobby.  Part of that hobby is getting your hands dirty.  This project certainly left me thoroughly cruddy.

Along with Ali’s lack of compassion for my plight she also seemed to lack any appreciation for what I navigated to get the truck back in one piece.  I can’t blame her I guess, it would be like her telling me the complex calculations she had to do with a tube feed at work I guess.

Anyway, if you would like to see all of the pictures I took along the way you can see them here.  I also shot some video of the mess I went through, the 24-25 minute adventure can be viewed below. Anyway, the moral of this story is in the big picture, although I learned a great deal about how to take my SSR interior apart, in a practical sense I would have been much better served just paying an installer to do the work.

http://www.youtube.com/watch?v=t6x2qFblMh4

Saturday we timed a 5K, it went fine, let’s move along.

So the Hooters Half Marathon was Sunday morning.  I was feeling upbeat about the weather forecast when I first saw it with predicted lows on Sunday in the low 50’s, great temps to run in.  Those hopes were later dashed when I saw that low temp was not going to hit until Sunday NIGHT.  Sunday morning the temperature at 7Am was supposed to be a balmy 75 degrees, shit.

When I woke up Sunday morning it was extremely windy.  I saw there was actually a wind advisory for later in the day.  Oh boy this is going to be fun.

We arrived at the race site a little after 6AM, the race started at 7.  After getting our bib number and race packet we hooked up with some of our fellow GCR members to hang out.  Most of the talk was about how tough the conditions were going to be with the wind.  I had decided ahead of time I was going to run shirtless because of the higher temperatures.  It would help keep me cooler and eliminate the painful nipple chafe I had last year.

As daylight increased we got a better look at the skies overhead, they looked quite menacing with low gray clouds zipping overhead at a rapid rate.

The race actually started about 10 minutes late which is pretty bad.  They made some long winded announcements that no one could hear as well as playing both the national anthem and Gold Bless America.  Ali and I wished each other luck and off we went.

So despite my severe lack of serious training and assorted nagging injuries leading up to the race I took off with the idea of still breaking the two hour goal I set as one of 2012’s to do’s.   It didn’t take long until that goal seemed to be very much in question.

No more than a few minutes into the race the skies opened up, it started to rain very, very hard.  The cold rain was wind blown and actually stung my exposed face and chest.  In no time at all the roads were bodies of water.  Everybody was thoroughly soaked from head to toe.

One of my first thoughts was “oh man, this is going to just crush the spirits of Ali & Christy”, both of whom were less than enthusiastic going into the event anyway.  Ali generally hates getting wet I could only imagine what she was thinking as each stride splashed down beneath her.

I was quite surprised when I found out later that the rain really didn’t bother her at all.  She said in fact she sort of enjoyed it.

The running with sopping wet sneakers immediately flashed me back to the Tough Mudder experience.  Thinking of that race also helped me mentally, realizing that compared to what we went through in the TM, getting rained on wasn’t a big deal.

The rain continued for a good 15-20 minutes.  In a way it was a good thing as it helped pull the humidity out of the air somewhat, helping to keep my body temp down.

Early on I was trying to find a run pacer target. The guy on the left was my first potential pacer.  He looked like a serious runner and was checking his pace often on his watch. (something I didn’t do the entire race)  He also appeared to be somewhere around my age.

For maybe a mile or so I stayed just off his back shoulder but then he started to slow down a bit and I felt like I needed to go faster if I was going to hit my goal so I passed him for good very early on.

A little later on I spotted another potential pacer, a younger muscle bound guy with a t-shirt that seemed to indicate he was part of a fire department.  I wound up following him for even less distance before I determined his pace was also too slow.

During the downpour there were a few brave spectators that didn’t mind getting wet to cheer us on which was really appreciated.  The most noticeable of all was the guy wailing on his bag pipes in the middle of the deluge with absolutely no cover overhead.

So since I couldn’t find what felt like an adequate pacer I spent most of the first half of the race just using rear ends as my “carrot”.  I slowly but surely picked off one rear end at a time.  In general I did almost exclusively passing for the race.  I bet for every one person that passed me I passed 15 more.

So I was coming up on the most difficult part of the race, the up and back over the 1 mile long bridge.  This was made exponentially more difficult by the very strong wind from the west that was smacking you in the face on the run out.

Usually when you get to the top of the bridge and begin the descent on the other side your speed picks up considerably.  Well this was the hardest I ever worked running DOWNHILL in my life.  The wind was so strong it resisted every step.

Of course the good news was on the way back across the bridge this wind was now helping to push you along.  The wind also was at your back for a good portion of the remainder of the race.

Once I got off the bridge at around the 9 mile mark I knew my two hour goal was in reach.  I also happened to finally pick up pace partner on the bridge.  Once again like last year, it was a woman.  I realized all I had to do was stick with her after she told me how she did two ultra-marathons last year as well as qualifying for the Boston Marathon.

Being able to carry an off and on conversation with her during the last third of the race really helped making those tough miles fall off pretty easily.  I was physically uncomfortable of course but not dying.  The skies had remained overcast the entire race so this really helped keep the temperatures reasonable.

Like I mentioned I hadn’t hardly looked at my watch other than to check my time at certain mileage markers.  Patty was doing it for me, telling me that we were running a strong 8:30 pace and that hitting my two hour goal was basically assured.

With about a mile to go I ran into one of the other GCR board members who was taking it easy by running an easy for him 2 hour pace.  I thanked Patty for helping me along and accelerated some more leaving her a little behind me.

At first I was having a bit of a hard time keeping up with Craig, I now was feeling pretty damn beat, that last half mile or so felt very long.  Once the finish line was a few hundred yards away I kicked in what I had left, leaving Craig behind as well.  I was very excited when I saw I could finish almost a full 5 minutes ahead of my what seemed to be ambitious 2 hour goal.  I crossed in 1:55:17, more than 16 minutes faster than my time last year. Here are the official results.

After collecting my finisher medal from the good looking Hooters girl I leaned over on the railing and briefly took in my achievement.  To smash my goal even with those type of race conditions was really something special to me.  I have always preached that actions are much more impressive than words.  It felt good to back that up.

So after downing a finish area Snickers bar and chugging a bottle of water I started looking for Ali.  Like I said, with the weather conditions I had no idea when she would finish.  I started walking back out on to the course, hoping to intersect with her and then help run her into the finish line.

I back tracked somewhere between a quarter and a half mile before I saw her.  I turned around and started jogging in with her.  Ali said nothing, I could tell by her heavy breathing she was really trying to finish hard.  When we got close I saw we were actually close to her 1/2 marathon PR time.  She wound up finishing just 21 seconds beyond her PR, a disappointment for her but based on the conditions and the course it was a really strong effort.

Like I said, before I saw her at the end I was almost positive the early rain and wind was going to suck the motivation right out of her.  Surprisingly she said she felt quite good almost the entire race.

We then waited for Christy who finished about 12 minutes behind Ali, putting in a strong showing for her as well, again made more impressive by the elements.

Ali was stoked to hear how well I did.  I told her that it was quite weird, when I woke up Sunday morning the number 1:55 literally was the first thing in my head.  I kid you not.  I thought it was odd I would even think about a finish time in that neighborhood.  It was amazing it came to be.  Visualization is powerful I guess huh?

So after the race we hung out for awhile.  At this point the cold front was blowing in, temperatures had dropped a good 10 degrees from the start of the race.  We stayed until maybe 10:30 before heading out, we were both cold and exhausted.

On the way home we both talked about various aspects of the race.  We were both happy with the way things turned out although Ali wished she could have found a spare 22 seconds somewhere.  It is hard to believe that I was not even going to do the race as late as last week and still managed to put in that showing.  So much of endurance racing is in your head, although I still attribute my significantly higher overall fitness level compared to the year before as a major contributor to my final result.

As you can imagine the rest of our Sunday was pretty tame.  I laid down for a couple hours with Ali but couldn’t get any real solid zzzz’s.  I wound up spending the rest of the day mostly toiling on the SSR audio project.

When I woke up Monday my stomach was feeling pretty awful and I was limping around severely.  My IT band felt like it was a foot too short.  I called off work to give myself a recovery day.  I feel much more human today.

The new IAC for the Tacoma showed up yesterday so it looks like I will get no break from my automotive upgrade/repair follies.  I want to get the new IAC in ASAP.  My hope is to be able to do it after work tonight.  I am hoping since I have run through the process once I can do it quickly this time around.

 

Another radio bug, 1/2 prep, new challenge, made in the USA??

Just for the hell of it I punched in my work address in the 930BT this morning to test out the navigation function of the radio.  I was pleased that my parking brake bypass evidently works, allowing me to use the navigation system when the truck is moving.  I however was not pleased that I couldn’t hear the voice NAV guidance.

I was getting annoyed when it sounded like the podcast I was listening to via wireless bluetooth seemed to be bouncing between the right and left speaker.  What I realized was this bouncing was when the navigation voice was speaking, it was just so low that I couldn’t hear it.

When I stopped to put air in a tire I verified that I have the voice volume option turned up to max volume.  However it almost sounded like the voice wasn’t coming through the speakers as all, it almost sounds like it is coming through the GMOS-04 adapter that is buried in the dash which has a small speaker used to replicate the factory chimes.

Why this would be the case is beyond me although it must mean I have something miswired in the harness.  I guess it is a good thing I plan to rip the entire thing apart again anyway.  I need a whole day to dedicate to nothing but getting this project cleaned up.

So I have been taking it a bit easy at the gym this week doing no running or leg weight work in anticipation of the extreme workload I will be placing upon them on Sunday in the half marathon.  Knock on wood my left knee/calf has felt ok for the last couple days.

Last night after work I filmed a video to introduce March’s BB challenge.  I am not quite sure how it wound up being over 8 minutes long.  For some reason in exercise videos where I am speaking to a camera I am far more chatty than I typically would be in most conversations with a flesh and blood human being.  Anyway, here is the video.

As I mentioned yesterday this weekend promises to be quite busy, trying to wedge in house chores and SSR audio work around timing one race and running another.  Oh well, it is better than sitting around collecting dust.

I was amazed when I saw the new pair of New Balance running sneakers Ali snagged for me were actually made in the USA, something that is simply unheard of anymore.

Now NB only manufactures about 25% of it’s sneakers in the US (7,000,000 or so) but that is 25% more than anybody else.  It definitely will make me lean towards buying New Balance for all my future athletic footwear.

 

Pioneer AVIC-X930BT install in my 2005 Chevy SSR

As promised, here is my experience installing my Pioneer AVIC-X930BT radio in my 2005 6 speed Chevy SSR. DISCLAIMER: I am not a professional car audio installer.  In fact this was the first radio I have installed in a vehicle in at least 25 years.  I have some decent technical ability and didn’t feel like forking over $500 extra to an installer to put the radio in.

My SSR had the factory Bose Premium sound system in it.  Although this radio worked fine I wanted the techo-geek features like GPS, Bluetooth support, Iphone integration and a rear back up camera.

I did a lot of reading leading up to the purchase and install of the equipment, especially on SSRFanatics.  Some people advised to rip out the existing Bose amp/speakers since they don’t have the best sound quality.  Not being an audiophile, I thought the existing system sounded just fine so I decided to leave the amp/speakers intact.

So with that being the case, here is the list of items I purchased from SonixElectronix.

1. Pioneer AVIC-X930BT (head unit)
2. Axxess GMOS-04 (wiring harness adapter designed for systems that include the Bose amp)
3. Metra 95-2009 (generic mounting plate/adapter)
4. Metra 40-GM10 (antenna adpater)
5. Pioneer ND-BC20PA (rear back up camera with parking assist)
6. Axxess ASWC (universal steering wheel controls adapter)

I already had the Ipod interface cable for the 930BT which I received as a Xmas present.

Now in addition to this I purchased several other items for the install like a set of nylon prying tools to prevent damaging the trim as well as some connectors for the various wires that will need to be connected between the radio harness and the GMOS-04.

The first order of business was getting the old radio out of the truck.  The first thing I did was pull a few fuses.

The first two I pulled were the radio and amp fuses located in the fuse box behind the passenger seat.  The third fuse was the air bag fuse which is located in the fuse box in the engine compartment.

Next up was to start the front dash disassembly. I removed the center silver trim piece using my nylon tools, it simply snaps out.

Once that was off there are 5 screws that need to be removed, 4 on the right of the steering wheel, one on the left of it.  You don’t need to remove the screws that connect to the lower dash.  It is pretty easy to tell which is which by looking at them.

Now comes the fun part, getting the dash panel popped off from the passenger air bag area.  This quite simply is a large pain in the ass.  At first I tried using my prying tools to help me but I eventually relied on simple hand strength to bend the corners of the air bag cover in such a way that they would pop through the dash opening.  The corners of the cover are pretty flexible but it still takes some serious work to get them through the opening.

I have read some suggestions that once you get the dash cover off you shave down the lip that the air bag cover sits in front of to make future reassembly and disassembly much easier.  Unfortunately I didn’t read that suggestion until after I had it back together.

In the picture to the left you can see the dash with the front panel completely removed.  Once the air bag cover is popped through the dash the rest of the removal is pretty easy.  The only other part that was a bit difficult to get off was the area around the steering wheel.  Dropping the tilt steering all the way down helped here.

All that remains is to remove the three screws that hold the factory radio in, slide the radio out and disconnect the wiring harness and antenna cable from the back of it. You are left with a nice clean hole to slide your new radio into.

So next I gathered up my GMOS-04 wiring harness (already did the parking brake bypass mod) and my factory Pioneer harness and did some reading.  To be quite honest, I felt quite overwhelmed at first, don’t be surprised if you feel the same way.  Relax, it will get better.

I was particularly confused by the GMOS-04 harness, it had a total of 5 wire connectors on it but I could only figure out where three of them went.  At first I thought somehow I ordered the wrong thing.

Slowly I started to figure out what went where.  One of the connectors was indeed unused, the gray one that only has two pins in it.  I have no idea what it’s intended use was.  The other small black connector turns out to be a quick and easy way to tie in the Axxess ASWC steering wheel control module.  I was confused by this because the AWSC comes with it’s own connector harness which I realized I simply didn’t need.

So I started going through the connections between the GMOS-04 and the Pioneer harness one by one, twisting the wires together but not crimping them until I knew everything was working.

For a ground I used a bare metal spot with a screw to the left and below the radio mounting location on the dash.  It was relatively close.

Eventually I got everything that was supposed to be connected, connected, or so I hoped.  I had a huge mess of wire in my hand that looked like shit.  I was not quite sure how I was going to transform it into a more organized mess.

I plugged all the harnesses in, put the fuses back in and nervously turned the key.  I was happy to see the radio light up and hear static from the speakers.  I tuned the radio to a local station and heard music.  Ok well that meant that I had the basic functions working.

I further tested the unit by stretching the GPS antenna and laying it on the ground in front of the truck so I could see if it picked up satellites, it did.  I also sloppily connected the rear camera just to see if that worked as well.  It did although it didn’t seem to have any connection to the truck being put in reverse. Oh well I can figure that out later.

Programming the AWSC was pretty easy once I realized I could use the built in connector on the GMOS-o4 to tie it in.  You basically just keep hitting the up volume button while turning on the car until the light stops flashing on the AWSC.  After that there are a series of flashes and if all goes well a solid red light at the end of the sequence, indicating the unit is now synched to your car and the new radio.

Ok so now I knew that everything more or less worked.  I took the harness back out and worked on securing the connections and cleaning up the wires the best that I could.  I read that some places recommend soldering the wire connections together.  I didn’t go this route, I just twisted the wires together and crimped them together securely with my bell connectors.

Even with a considerable amount of time spent cleaning everything up I wasn’t all that pleased with the end result.  You are shoving a lot more junk into the dash than what was in there originally.  I would be curious to see what a “pro” installation looks like in comparison.

So finally I was ready to put the radio in for “real”.  I mounted the GPS antenna up under the dash on top of a metallic cross brace that the magnetic antenna snapped on to securely.  I had read elsewhere this was a nice out of the way to do it instead of slapping it somewhere on the exterior of the truck.

I also fed up all of the various external connections that would connect to the radio from the floor up through the radio opening.  These included the wires for the back up camera, Bluetooth mic, and the Ipod interface cable.

I connected the GMOS-04 harness to the factory harness, the antenna to the antenna adapter, slid the AWSC onto a piece of metal that looked like a good resting place and tried to slide the 930BT back into the slot.  Oh I forgot to mention that of course I had already attached the generic mounting plate to the new radio so the tabs line up with the factory mounting holes.

Well I felt resistance as I tried to steer the radio in place.  Of course I knew the resistance was from the huge collection of stuff that is behind it.  I jammed my hand uncomfortably into the hole where the right air vent is normally located and got my fingers under the wires behind the radio to lift them up and out of the way so they aren’t pinned behind the radio.  It took a lot of frustrating manipulation but eventually I got the radio fully seated.

Ok so now I needed to make sure the radio still works with it mounted in place.  Guess what? It didn’t.  The thing was dead a s a doornail, I was pissed.  At first I just hoped I simply didn’t push one of the fuses back in but they were all snugly inserted.

Out came the multimeter and I started to troubleshoot where I was losing juice.  It took me a long time to figure out the problem and I was getting increasingly despondent before I did.  On the GMOS-04 the pin for the yellow wire, which is used for accessory power was pushed back a bit for some reason.  I pushed it from behind so it snapped firmly back in place.  Imagine my relief when everything fired up normally, whew.

Ok I thought the hardest part was behind me, putting the dash back together shouldn’t be that bad, right? Wrong.

If I did that little mod I mentioned around the air bag opening I am sure this would have went better.  I determined the air bag going back through the hole was the first step in getting everything else back together.  Doing so again was tough as hell, requiring even more vigorous hand manipulation than required to remove it.  I was quite frustrated but eventually persistence won out and I forced the cover back through the hole in the dash.  I wasn’t out of the woods yet.

In addition to getting the air bag cover back through the hole, you also have the difficult task of getting the dash air vents lined up with the ducts behind them.  It was tough as well.

Then I ran into another issue, the dash didn’t seem to want to snap back together a 100%.  Eventually with some vigorous pounding with the heel of my hand it did appear to snap into place but then I noticed the radio was sitting oddly.  Well of course I couldn’t have this and was dejected knowing that it meant I had to pull the dash cover all the way off again.

Once I did I saw that my pounding had snapped one of the plastic mounting tabs on the mounting kit, shit. I also realized that I must have had the radio mounted more forward than the factory radio, causing the tight fit.  The sides of the 930 BT have a number of mounting holes with different letters next to them but I just used what looked right.

So I had to run off to Best Buy to get another mount kit.  Putting it on meant I had to slide the radio out and then repeat the incredibly annoying process of getting everything shoved back in there.  I was pretty damn miserable at this point.

After some more futzing around I got the radio and dash back on albeit not perfectly.  There is still some slight issues with the fit and finish.  The radio still seems to protrude a fraction of an inch too far, causing the silver trim piece to be shifted down just enough that it causes some drag on the climate controls which will need to be addressed.

To the casual observer/rider they won’t notice the wart but I know it’s there.

I didn’t mount the camera in the license plate area yet, that shouldn’t be too tough to handle.

I didn’t try to be very fancy with my Ipod cable routing.  I have seen some guys modify their ash tray or glove box so it can house their Iphone.  I simply ran the wire along the passenger side of the center console and ended it in the parking brake area so I can just plop my phone there.  Since the radio supports Bluetooth streaming the cable isn’t really needed for a lot of stuff anyway.

I decided to mount the mic for my Bluetooth up to the driver side visor.  I have seen some guys mount the mic on the steering column but I think up on the visor is less obtrusive while being more effective since it is closer to your mouth.

There are some outstanding bug/question/issues I have with the radio which I have yet to address.

They are the following.

The rear backup camera does not flip over to the rear view automatically when the truck is put into reverse. (six speed manual) I triple checked that I had the correct wires connected between the GMOS-04 and the Pioneer wiring harness to support this but it still doesn’t work.

The voice guidance volume level seems too low even with having it configured to max volume.  It also doesn’t seem to cut out the music source when it gives guidance which makes no sense.  I will need to play with it some more I suppose.  The cabin noise in an SSR could make hearing the voice guidance tough I guess.

I think it’s weird that the standard map display does not have an option to display vehicle speed.  That is kind of annoying.

When I first tried the radio on a test drive I noticed my tach was “sticking”, reading about 1500 rpm’s higher than normal.  Luckily that problem seemed to fix itself.  I can only guess it was related to the banging to get the dash back together.

Be careful when banging on the dash.  I inadvertently knocked out some fins on the air vents.  I didn’t find all of them.

Other than those few items I am very pleased overall with the radio.  The GPS works well, the Iphone integration is pretty damn slick and I find the overall radio user interface visually pleasing and easy to use.  In fact it makes me want another one to put in my daily driving 99 Tacoma but that would be too financially painful at the moment.

As I address my remaining issues and complete my camera installation I will report back with more results.  I hope you found this somewhat helpful.  I may look into removing the top dash pad to make guiding the harness and wires back into the mounting location cleaner.

If you would like to see all of the pictures I took during the install you can see them here.

 

 

 

 

So far

Dad, Teresa and the dogs arrived right around 5 on Tuesday afternoon.  Their arrival was delayed by dad’s drowsiness, he actually stopped at a rest stop and took a nap on a bench.  It was no big deal to me since I had spent the majority of the day working on the SSR radio upgrade which will be receiving it’s own dedicated blog entry at some point.    Let’s just say it has been as challenging as I expected. For now if you would like to see the pictures of the install you can see them here.

The dogs took next to no time to become re-acclimated, they immediately  took off running around the yard, it was very cute.  Clara also wasted no time getting re-acclimated with our pond, jumping into it within the first 10 minutes.

Tuesday evening Ali made nice salads and we reheated some of the rice pilaf and sweet potato patties that she also made a couple days ago.

Yesterday I again spent a considerable amount of time out in the garage with the SSR with my dad offering an assist during certain points of the install.  We broke it up with a trip out in the party van with all four dogs.  We had lunch at Panera and I needed to stop at Best Buy to buy another radio mounting kit after we accidentally snapped a bracket on the old kit via pushing on the dash too hard.

Teresa bought food to make a really nice meal that we enjoyed out on the lanai last night after Ali got home from track practice.

Today dad and I will be driving over to Fort Lauderdale to pick up Patrick and his girlfriend Maureen.  He is flying in from Pittsburgh.  Once they get here we will start doing more sight seeing and tourist stuff.